Just How To Install A Bath Tub (For Novices).
Just How To Install A Bath Tub (For Novices).
Blog Article
Do you find yourself searching for insight concerning Tools You Need to Install a New Bathtub ?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard project. If the old tub is easily accessible, the project can move easily; if you have to open a wall to eliminate the old bathtub and position the new tub, the job is a lot harder. In either case, the job is within a home handyman's skills, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have certified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need an expert plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your washroom if you have already bought a new tub and don't need to change the arrangement of your previous water supply pipes.
Your tools and product list need to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the restricted access that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be attached to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wood boards under its feet, position the tub in the required placement. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bathtub up until the level reviews degree.
To install taps, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression join; then do the exact same for the other tap.
Activate the water system and also examine all joints and new pipework for leaks as well as tighten them if essential. Fill the bathtub and likewise examine the overflow outlet and the normal outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub ought to wait up until the tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Planning for the Setup
To start with, the supporting frame supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about issues with dampness as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to enable the activity experienced when the tub remains in use. The sealant can split rather early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave a short review down the page. We will be glad to hear your reactions about this page. In hopes to see you back again later on. Remember to take the time to share this blog if you appreciated it. We truly appreciate reading our article about How to Install a Bathtub Yourself.
Quote Report this page